Free practice test · 10 questions
NICET Inspection and Testing of Water-Based Systems Level II Practice Test
10 questions from the ForemanForge Inspection & Testing Level II course, spread across NICET's content outline. Pick an answer to check it. Every answer explains why and shows where to find it in NFPA 20, NFPA 25, NFPA 72 and NFPA 291, the books NICET lets you bring to this exam.
These are ForemanForge practice questions written to NICET's outline, not questions from the NICET exam.
Question 1 · 2.1 Safety
NFPA 25's threshold for stepping up mitigation on an impaired system: out of service for more than:
Show the answer and where to find it
Answer: C. 10 hours in a 24-hour period
Past 10 hours in 24, 'we'll have it back soon' is no longer a mitigation plan. A is wrong — 1 hour is far too short; minor impairments routinely exceed this without escalation. B is wrong — 4 hours in 24 is below the threshold; the standard allows up to 10 hours before mandatory mitigation escalation. D is wrong — 72 hours is far beyond the threshold; the fire watch or evacuation decision must be made at 10 hours, not 72.
Find it: NFPA 25 (2023) §15.5.1.1 — Impairment mitigation threshold (10 hours in 24 → fire watch or evacuation).
Question 2 · 2.2 Communication
Your report lists a corroded FDC swivel. Three weeks later the owner calls: "You inspected it — why didn't you fix it?"
What is the correct position, supported by your paperwork?
Show the answer and where to find it
Answer: A. The inspection contract covers finding and reporting
Reporting versus repairing is the boundary — and it only protects you if the report and notification were documented. B is wrong — fixing it free concedes a repair duty the contract doesn't carry; the inspection contract covers finding and reporting. C is wrong — on-the-spot repairs need the owner's authorization; the inspection contract doesn't include them. D is wrong — the FDC belongs to the owner's system; the fire department uses it but doesn't maintain it.
Find it: NFPA 25 (2023) §4.1 — Owner responsibilities (correction is separate from inspection) / trade practice (scope discipline: reporting vs. repairing).
Question 3 · 2.3 Perform, Document, and Interpret Intermediate ITM Tasks
Annual at a strip mall: (1) one storefront's OS&Y closed with no tag, (2) a painted sprinkler in the salon, (3) a missing FDC cap.
What are your classifications?
Show the answer and where to find it
Answer: D. (1) impairment; (2) critical deficiency; (3) noncritical deficiency
One finding triggers the impairment machinery tonight; the other two ride the report with different urgencies. A is wrong — it swaps the last two; paint on a sprinkler degrades performance (critical), while a missing FDC cap doesn't (noncritical). B is wrong — a closed valve feeding one storefront takes that storefront's protection offline; that's an impairment, not a critical deficiency. C is wrong — one painted sprinkler degrades performance but doesn't take the system out of service; it's a critical deficiency, not an impairment.
Find it: NFPA 25 (2023) §3.3 — Definitions (impairment, critical deficiency, noncritical deficiency) / §15.1 — Impairment classification / §5.2.1.1 — Painted sprinkler (critical) / §13.7 — FDC cap (noncritical).
Question 4 · 2.3 Perform, Document, and Interpret Intermediate ITM Tasks
During the standpipe 5-year flow test at the roof outlet, the system can't reach the required residual pressure, though the pump passed its annual test last month.
What is your interpretation?
Show the answer and where to find it
Answer: A. Something between pump and roof is robbing pressure
A healthy pump with a failing remote outlet points at the path — that's a diagnosis decision, not a retest decision. B is wrong — nothing says last month's pump test was bad; the pump passed, so the problem is between pump and roof. C is wrong — the system was designed to serve this outlet; the problem is in the path. D is wrong — there's no 10% allowance; a failing result gets investigated, not accepted or retested until it passes.
Find it: NFPA 25 (2023) §6.3.1 — Standpipe flow test interpretation (healthy pump + failing remote = path problem: valve, PRV, obstruction) / Ch. 6 flow test diagnosis.
Question 5 · 2.3 Perform, Document, and Interpret Intermediate ITM Tasks
Warehouse dry system, February. Records show air at 40 psi in October, 38 in December; today it reads 32 psi, the compressor cycles every few minutes, and the low-air alarm hasn't sounded.
What are your decisions?
Show the answer and where to find it
Answer: B. Two findings: an active air leak and a low-air switch that failed to signal
The trend line says leak; the silent switch says the early-warning layer is dead too — both go in the report with urgency. A is wrong — cold may shave a psi or two, but an 8-psi slide with a compressor that won't rest is a leak. C is wrong — raising the setting doesn't fix the leak; it masks the symptom and puts air above the manufacturer's band, which delays the trip. D is wrong — with the compressor off, the leak drains the air and trips the valve.
Find it: NFPA 25 (2023) §13.4.2 — Dry pipe valve inspection (air pressure trending, leak detection) / §13.3.2 — Low-air supervisory switch testing.
Question 6 · 2.3 Perform, Document, and Interpret Intermediate ITM Tasks
Since the 2020s editions of NFPA 25, antifreeze solutions in sprinkler systems must be:
Show the answer and where to find it
Answer: A. Listed antifreeze solutions installed per their listing
Unlisted, over-concentrated solutions proved ignitable at discharge — the listing requirement closed that chapter. B is wrong — the premixed glycerin and propylene glycol limits were the older interim rule for existing systems; the current rule requires listed solutions installed per their listing. C is wrong — a field-mixed solution isn't a listed fire protection solution; site mixing is exactly what the listing requirement ended. D is wrong — a good freeze point isn't enough; the solution must be listed and installed per its listing.
Find it: NFPA 25 (2023) §5.3.3 — Antifreeze systems (listed solutions, installed per listing) / antifreeze solution requirements.
Question 7 · 2.4 Perform, Document, and Interpret ITM Tasks for Water Supplies
Annual test, pump rated 750 gpm @ 120 psi. Results: churn 165 psi; 100% point on spec; at 150% (1,125 gpm) discharge is 70 psi with suction dropping near zero.
What is the correct read?
Show the answer and where to find it
Answer: D. Churn passes, the 150% point fails — investigate the suction path
Do the arithmetic (140% and 65% of RATED) and read the suction gauge — the supply, not the impeller, is the lead suspect when suction dives at high flow. A is wrong — 'full pass' is wrong; 70 psi is below 65% of 120 (78 psi), so the 150% point fails. B is wrong — 'fail the churn point' is wrong; 165 ≤ 168 (140% of 120), so churn passes. C is wrong — 'pass everything, gauges drift' is wrong; the 150% point fails and the collapsing suction points to the supply, not the gauge.
Find it: NFPA 25 (2023) §8.3.3 — Annual flow test (150% ≥ 65% rated: 70 < 78 = FAIL) / NFPA 20 §4.3.2 — Pump characteristics (suction collapse = supply limitation) / §8.3.7 — Investigation.
Question 8 · 2.4 Perform, Document, and Interpret ITM Tasks for Water Supplies
NFPA 25's threshold for investigating annual flow test degradation: performance falling more than:
Show the answer and where to find it
Answer: D. 5% below the original acceptance/nameplate performance
The 5% rule turns 'a little low' into a required investigation before it becomes a failure. A is wrong — 'any measurable amount' is too sensitive; normal minor fluctuations don't trigger investigation; the 5% threshold is the standard's trigger. B is wrong — 10% is the main drain comparison trigger, not the pump test; pump degradation is investigated at 5%. C is wrong — 20% is far too loose; the standard requires investigation at 5%.
Find it: NFPA 25 (2023) §8.3.7 — Annual flow test (performance >5% below acceptance/nameplate → investigate).
Question 9 · 2.4 Perform, Document, and Interpret ITM Tasks for Water Supplies
January, -10°F week forecast. At a suction tank site the low-water-temperature alarm is out of service and the last logged water temperature — a month old — was 42°F.
What do you do?
Show the answer and where to find it
Answer: B. Verify water temperature now and restore the monitoring
A dead low-temp alarm in an arctic week means the supervision layer is gone — manual checks fill the gap and the outage goes on the report. A is wrong — a month-old reading says nothing about this week; with the alarm dead, the temperature must be verified now. C is wrong — antifreeze doesn't go in a suction tank; heat and supervision are the protection. D is wrong — -10°F is an immediate freeze risk; the alarm can't wait for the next visit.
Find it: NFPA 25 (2023) §9.4 — Water storage tanks (verify temperature, restore supervision, manual checks on cold-weather schedule) / §9.2 — Tank supervision (alarm outage = finding).
Question 10 · 2.5 Internal Obstruction Investigation
A city crew repaired a broken 8-inch main at the street last month. This month, the site's main drain test discharges muddy water and fine gravel for the first several seconds. The owner asks if it matters.
What do you explain?
Show the answer and where to find it
Answer: C. The main break likely pushed debris into the supply — investigate now
Gravel in the drain discharge after a street repair is the textbook trigger scenario — the debris is already inside the fence. A is wrong — gravel in the drain after a main break is a trigger, not seasonal runoff. B is wrong — the city flushing its own main doesn't clean the private supply; gravel in the drain proves debris is already inside. D is wrong — gravel and soil don't flush out with drain tests; they settle in the system and require investigation and flushing. Examine the supply-side strainers, riser check, and entry points now rather than waiting for the 5-year.
Find it: NFPA 25 (2023) §14.3.1 — Obstruction investigation triggers (broken main near supply: debris in drain discharge) / Ch. 14 triggers.
How ready are you for the real exam?
ForemanForge's readiness meter gives you one score for the NICET Inspection & Testing Level II exam. It counts every question you answer in the lessons and practice, scores you on each work element in NICET's content outline, and weights each one by its share of the exam.
- Your score shows after 20 answered questions and moves as you study.
- It shows which work elements are pulling your score down, so you know what to study next.
- Timed exams count, and it won't read Exam Ready until you've scored 70% or better on a timed exam in the last 60 days.
- Building · under 60
- Borderline · 60–74
- Exam Ready · 75 and up
The score is an estimate of how you'd do on the exam, not a guarantee of passing. NICET doesn't publish a fixed pass mark.
Start studying for Inspection & Testing Level II
The first lessons of every level in each track are free. Have an account? Log in
Keep going
- NICET Inspection & Testing Level II exam guide: what's on the exam, how it runs and which books you can bring.
- NICET Inspection & Testing Level I practice test
- NICET Inspection & Testing Level III practice test
All NICET exam guides (Inspection and Testing of Water-Based Systems and the other programs ForemanForge covers)