Free practice test · 10 questions

NICET Fire Alarm Systems Level I Practice Test

10 questions from the ForemanForge Fire Alarm Level I course, spread across NICET's content outline. Pick an answer to check it. Every answer explains why and shows where to find it in NFPA 72, NFPA 70 / NEC and Ugly's Electrical References, the books NICET lets you bring to this exam.

These are ForemanForge practice questions written to NICET's outline, not questions from the NICET exam.

Answered 0 of 10
  1. Question 1 · 1.1 Installation

    Walking your floor before rough-in, you notice the drawings show no pull station at one stairwell exit door — the nearest is around a corner, well past 5 ft from the doorway. You:

    Show the answer and where to find it

    Answer: B. Flag it to your supervisor — stations belong within 5 ft of each exit

    Trainees install per the drawings AND report what looks wrong with them — both halves are the job. A is wrong — adding a station on your own is an unauthorized design change; the drawings are approved, and field changes require supervisor direction. C is wrong — saying nothing leaves a potential code violation in place; reporting gaps is part of the trainee's job, not just installing. D is wrong — relocating an exit sign does not fix the missing pull station; the exit and the pull station are separate devices with separate requirements.

    Find it: NFPA 72 (2022) §17.15.9.4, manual fire alarm boxes — location relative to exits.

  2. Question 2 · 1.1 Installation

    The foreman from another crew hands you a red-jacketed spool for the return-air plenum run: "Red means plenum, go." The jacket legend reads FPL. You:

    Show the answer and where to find it

    Answer: C. Show him the legend — FPL is not plenum-rated; the run needs FPLP

    The legend beats the color and the confidence; a wrong pull through a plenum comes out at inspection. A is wrong — the foreman's rank does not override the cable listing; FPL is not plenum-rated, and the legend is the authority, not the color or the person. B is wrong — pulling half the run with the wrong cable means half the run comes out at inspection; the correct action is to stop and get the right cable before pulling. D is wrong — painting over the legend does not change the cable's listing; the rating is determined by the manufacturer's testing, not field markings. A permitted substitute cable also works.

    Find it: NFPA 70 (2020) §760.154, cable applications — plenum / Table 760.154(A).

  3. Question 3 · 1.1 Installation

    Trimming out a conventional zone, you find the EOL resistor screwed to the zone terminals inside the FACU "so it's easier to check." The circuit reads normal. The problem:

    Show the answer and where to find it

    Answer: A. The field wiring is now unsupervised — the EOL must live at the far end of the circuit

    The circuit reads normal precisely BECAUSE the supervision loop never leaves the cabinet — that's the failure, not the proof. B is wrong — a normal reading means the panel sees the EOL, but since the EOL is inside the panel, the field wiring is not in the supervision path; a break goes undetected. C is wrong — the resistor value comes from the panel manufacturer and doesn't change with wire length; the problem is where it sits, not its value. D is wrong — with the EOL in the cabinet, none of the field wiring is in the supervision path, not just the last device; a break anywhere out there goes undetected.

    Find it: NFPA 72 (2022) §12.6, pathway supervision — EOL device location / Ch. 12.

  4. Question 4 · 1.1 Installation

    In a small office you find the ceiling smoke detector mounted directly in front of a supply air diffuser, streamers on the diffuser blowing straight across the detector. The concern:

    Show the answer and where to find it

    Answer: B. Supply airflow can dilute and deflect smoke away from the chamber, delaying response

    Report it for relocation per direction; airflow placement problems are exactly what a trainee's eyes are for. A is wrong — diffuser noise is not a detector concern; the issue is airflow deflecting smoke, not acoustic interference. C is wrong — supply air temperature is not the concern; the issue is airflow pattern, not temperature. D is wrong — supply air blowing across a detector dilutes and deflects smoke away from the chamber, delaying response; it does not help smoke reach the detector.

    Find it: NFPA 72 (2022) §17.7.7.3, smoke detectors — location relative to supply air / Ch. 17.

  5. Question 5 · 1.1 Installation

    An electrician offers you space in his conduit: "Plenty of room next to my 277 V lighting circuit for your panel loop." You:

    Show the answer and where to find it

    Answer: C. Decline and route separately

    Induced noise and fault exposure are why 760 keeps PLFA circuits out of power raceways — separation is the default, not the exception. A is wrong — free raceway does not override the separation requirement; sharing with 277 V lighting exposes fire alarm circuits to induced voltage and fault contact. B is wrong — twisting does not eliminate the separation requirement; the code prohibits sharing raceways with power circuits, and twisting is not a permitted substitute for separation. D is wrong — wire color does not address the safety issue; the separation requirement is about induced voltage and fault contact, not wire identification.

    Find it: NFPA 70 (2020) §760.136, separation from power conductors / Art. 760.

  6. Question 6 · 1.2 Maintenance

    Semiannual battery test on a 24 V panel with two 12 V VRLA units, fully charged, charger connected. Your meter reads 14.10 V on one unit and 13.08 V on the other. You:

    Show the answer and where to find it

    Answer: D. Record a failure — a unit under 13.26 V means battery replacement — and report it

    The cell/unit voltage test is read fully charged with the charger connected. The 2022 table says to replace the battery when any cell/unit measures less than 13.26 volts. 13.08 V fails, however high its partner reads. A is wrong — the total hides a weak unit, and the criterion is per cell/unit. B is wrong — the table specifies the reading on charge, and that's the condition the 13.26 V figure is written for. C is wrong — 13.08 V is already under 13.26 V; the unit fails today, not at the next visit.

    Find it: NFPA 72 (2022) Table 14.4.3.2, item 9 — cell/unit voltage test: replace below 13.26 V.

  7. Question 7 · 1.2 Maintenance

    The service ticket says "replace bad horn/strobe, Room 214." The old unit is 75 cd; the only spare is a 15 cd of the same series, and the wiring fits. You:

    Show the answer and where to find it

    Answer: D. Hold — candela is part of the design; get the correct rating per your supervisor

    "Fits electrically" is not "equivalent" — replacement means matching the designed performance, not just the terminals. A is wrong — same series does not mean same candela; a 15 cd strobe in a space designed for 75 cd leaves the room under-signaled and non-compliant. B is wrong — relabeling a 15 cd strobe as 75 cd is falsification; the device produces 15 cd regardless of the label, and the space remains under-signaled. C is wrong — leaving the space with no appliance is an impairment; the correct replacement must be obtained, not skipped.

    Find it: NFPA 72 (2022) §18.5, visible signaling — candela rating / §14.5, maintenance — equivalent replacement.

  8. Question 8 · 1.2 Maintenance

    At the inspector's test connection you open the valve and start your stopwatch. The panel receives the waterflow alarm at 2 minutes 30 seconds. You:

    Show the answer and where to find it

    Answer: B. Record it as a failed/deficient result — initiation must occur within 90 seconds — and report it for correction

    150 seconds is not 90; a late waterflow signal is a finding with a number attached, and the number decides. A is wrong — eventual initiation is not the requirement; the code requires initiation within 90 seconds, and 150 seconds is a failure. C is wrong — blaming the stopwatch without calibrating or verifying it is not a valid response; the timing is a measured result that must be recorded. D is wrong — retesting until a random pass is not valid; the failure indicates a problem (delay, obstruction, switch adjustment) that must be corrected, not gambled past.

    Find it: NFPA 72 (2022) §17.13, waterflow alarm-initiating devices — 90-second initiation / Ch. 17.

  9. Question 9 · 1.2 Maintenance

    Starting the annual secondary-power test, you open the FACU's branch circuit breaker. Five minutes later the panel is running on batteries with NO trouble showing. You:

    Show the answer and where to find it

    Answer: A. Record a deficiency — losing primary power must produce a trouble — and report it

    The secondary-supply test starts by disconnecting primary power and verifying the required trouble indication for its loss. The control unit's functions test also covers power-supply supervision for loss of AC. A panel that goes to batteries silently will drain them in silence. B is wrong — a working transfer doesn't excuse missing supervision. C is wrong — the trouble indication is the first thing the test verifies, so its absence is a finding now. D is wrong — cycling the breaker until it works hides a fault you're supposed to report.

    Find it: NFPA 72 (2022) Table 14.4.3.2, secondary power supply — verify trouble on loss of primary power.

  10. Question 10 · 1.3 Submittal Preparation and System Layout

    When a system is modified (devices added, circuits changed), the Record of Completion:

    Show the answer and where to find it

    Answer: D. Is revised/updated so the certifying document keeps matching the installed system

    The birth certificate stays current for life — a modified system with a stale record is a documentation deficiency. A is wrong — the Record of Completion is not frozen; it is revised when the system is modified so it matches the installed system. B is wrong — a service ticket isn't the certifying document; the Record of Completion itself gets revised. C is wrong — waiting for the annual leaves the record stale; it's revised as part of the modification.

    Find it: NFPA 72 (2022) §7.5.6, record of completion — revisions after modification / Ch. 7.

How ready are you for the real exam?

Example of the readiness meter: 68, Borderline.

ForemanForge's readiness meter gives you one score for the NICET Fire Alarm Level I exam. It counts every question you answer in the lessons and practice, scores you on each work element in NICET's content outline, and weights each one by its share of the exam.

  • Your score shows after 20 answered questions and moves as you study.
  • It shows which work elements are pulling your score down, so you know what to study next.
  • Timed exams count, and it won't read Exam Ready until you've scored 70% or better on a timed exam in the last 60 days.
  • Building · under 60
  • Borderline · 60–74
  • Exam Ready · 75 and up

The score is an estimate of how you'd do on the exam, not a guarantee of passing. NICET doesn't publish a fixed pass mark.

Start studying for Fire Alarm Level I

7 lessons, 336 practice questions, a full-length 85-question timed exam and your readiness score for the NICET Fire Alarm Systems Level I exam.
Start free

The first lessons of every level in each track are free. Have an account? Log in

Keep going

All NICET exam guides (Fire Alarm Systems and the other programs ForemanForge covers)