Free practice test · 10 questions

NICET Water-Based Systems Layout Level III: Hydraulics and Water Supply Planning Practice Test

10 questions from the ForemanForge WBSL Level III: Hydraulics and Water Supply Planning course, spread across NICET's content outline. Pick an answer to check it. Every answer explains why and shows where to find it in NFPA 13, NFPA 14, NFPA 20, NFPA 291 and Brock, the books NICET lets you bring to this exam.

These are ForemanForge practice questions written to NICET's outline, not questions from the NICET exam.

Answered 0 of 10
  1. Question 1 · 3.9 Calculate Standpipe Systems

    During a standpipe acceptance test, the most remote 2½" outlet delivers 250 gpm at 92 psi residual with the system at design flow.

    Per NFPA 14, this system:

    Show the answer and where to find it

    Answer: A. Fails — the Class I minimum is 100 psi

    92 < 100 psi minimum for Class I — the system fails the acceptance test regardless of pump status or AHJ preference. B confuses Class I (100 psi) with Class II (65 psi). C delegates a code requirement. D is irrelevant — the test is at design flow.

    Find it: NFPA 14 (2019) §7.8.1 — minimum residual pressure; Ch. 11 — acceptance tests.

  2. Question 2 · 3.10 Calculate Water Supply with Pumps

    System demand: 750 gpm @ 85 psi (at the pump discharge reference). Suction supply provides 42 psi at 750 gpm.

    The required pump boost is:

    Show the answer and where to find it

    Answer: B. 43 psi

    Boost = demand − suction AT THE SAME FLOW: 85 − 42 = 43 psi. D forgets the suction entirely (sizing the pump for total head) — a real-world error that buys a pump twice as big as needed. A (35) uses the wrong suction. C (50) uses the wrong demand.

    Find it: Brock 3rd ed. — fire pumps (net pressure = demand − suction at the same flow); NFPA 20 (2022) §4.10 — centrifugal fire pump capacities.

  3. Question 3 · 3.10 Calculate Water Supply with Pumps

    Two identical fire pumps, each rated 500 gpm @ 75 psi boost.

    Two in PARALLEL, each at rated point:

    Show the answer and where to find it

    Answer: A. 1000 gpm @ 75 psi boost

    Parallel adds flows at common boost. But the SUCTION main now sees 1000 gpm — its droop at the doubled flow can eat the gain. Re-run the suction curve before celebrating. B is series, not parallel. C doubles both — neither series nor parallel. D is a single pump at 150%.

    Find it: NFPA 20 (2022) Ch. 4 — general requirements (multiple pumps); §6.2 — single-pump performance.

  4. Question 4 · 3.10 Calculate Water Supply with Pumps

    Suction supply: static 58, residual 46 @ 1,200 gpm. Pump: rated 1,000 gpm @ 65 psi boost (150% point: ≥ 42.25 psi @ 1,500 gpm). Demand: 1,100 gpm @ 100 psi.

    Total delivery at 1,100 gpm (chord interpolation):

    Show the answer and where to find it

    Answer: C. 108.2 psi — passes by 8.2

    Suction at 1,100: 58 − 12 × (1100/1200)¹·⁸⁵ = 47.78 psi. Boost at 1,100 (chord rated→150%): 65 − 22.75 × (100/500) = 60.45 psi. Total 108.2 vs 100 → +8.2 psi. B used the test residual (46) instead of suction-at-flow; D used static (free pressure that vanishes at 1,100 gpm); A applied the 150% boost floor at the wrong flow. Same flow, both curves, every time.

    Find it: NFPA 20 (2022) §6.2 — pump performance; Brock 3rd ed. — pump + supply curves.

  5. Question 5 · 3.11 Hydraulic Calculation Principles

    System C (150 gpm @ 48 psi) joins a node governed at 65 psi.

    Its balanced flow is:

    Show the answer and where to find it

    Answer: B. 174.6 gpm

    K = 150/√48 = 21.65, so Q' = 21.65 × √65 = 174.6 gpm — same as 150 × √(65/48). That's the K-factor balance. C (176.7) uses the 0.54 exponent, which belongs to water-supply curves, not balancing; on K = 21.65 it would need 66.6 psi, 1.6 psi off the node. D (203.1) is linear. A (165.0) just bumps the flow 10%. Two gpm apart: carry √P through the K-factor.

    Find it: NFPA 13 (2022) §28.2.2.4 — hydraulic junction points (K = Q/√P balancing).

  6. Question 6 · 3.11 Hydraulic Calculation Principles

    An end head requires 16.0 psi; accumulated friction back to the riser totals 12.5 psi; the head sits 30 ft above the BOR gauge.

    Pressure required at the BOR:

    Show the answer and where to find it

    Answer: D. 41.5 psi

    16.0 + 12.5 + (30 × 0.433 = 13.0) = 41.5 psi. A forgot elevation entirely — the three-bucket sum (outlet pressure + friction + elevation) IS the hydraulic calculation; every III-B stack question is these three terms wearing different numbers.

    Find it: NFPA 13 (2022), Ch. 28 — total demand pressure.

  7. Question 7 · 3.11 Hydraulic Calculation Principles

    200 gpm enters a loop: Path A 120 ft of 2" Sch 40 (ID 2.067"), Path B 180 ft of 2½" Sch 40 (ID 2.469"), C=120.

    Using FLC_A·L_A·Q_A^1.85 = FLC_B·L_B·Q_B^1.85, the ratio Q_A/Q_B is:

    Show the answer and where to find it

    Answer: B. 0.78

    Q_A/Q_B = (FLC_B·L_B / FLC_A·L_A)^(1/1.85) = 0.78. A (0.67) is the length ratio (120/180 — ignores diameter). C (0.84) is the bare diameter ratio (2.067/2.469 — ignores length and both exponents). D (1.28) is the inverted ratio. The exponent is 1/1.85 = 0.54 — nothing else.

    Find it: NFPA 13 (2022) §28.2.2.1 — Hazen-Williams formula; §28.2.2.4 — pressures balance at junctions.

  8. Question 8 · 3.11 Hydraulic Calculation Principles

    For a 1,500 ft² remote area, the design area's dimension parallel to the branchlines must be at least:

    Show the answer and where to find it

    Answer: C. 46.5 ft

    L = 1.2√A = 1.2 × √1500 ≈ 46.5 ft. The remote area is a rectangle stretched along the branchlines — this prevents cherry-picking a compact square that under-stresses the piping.

    Find it: NFPA 13 (2022) §28.2.4.2.1 — design area length (1.2√A along the branch lines).

  9. Question 9 · 3.11 Hydraulic Calculation Principles

    Per NFPA 13 (2022), when flow goes straight through the RUN of a tee (no turn), the equivalent length is:

    Show the answer and where to find it

    Answer: D. Zero

    Straight-through run flow is treated as straight pipe — no equivalent length added. The equivalent length applies only when flow turns 90° through the branch.

    Find it: NFPA 13 (2022) Table 28.2.3.1.1 — straight-through tee.

  10. Question 10 · 3.11 Hydraulic Calculation Principles

    A K=11.2 head must supply 16.8 gpm by density (0.10 gpm/ft² × 168 ft²). Pressure check: (16.8/11.2)² = 2.25 psi — below the 7 psi floor. The flow you enter for this head is:

    Show the answer and where to find it

    Answer: D. 29.6 gpm

    When the 7 psi floor governs, flow is recomputed UPWARD: Q = 11.2 × √7 ≈ 29.6 gpm. The floor never lets you keep the density minimum at an illegal pressure — big-K heads at low densities hit this constantly.

    Find it: NFPA 13 (2022), Ch. 28 — minimum operating pressure.

How ready are you for the real exam?

Example of the readiness meter: 68, Borderline.

ForemanForge's readiness meter gives you one score for the NICET WBSL Level III: Hydraulics and Water Supply Planning exam. It counts every question you answer in the lessons and practice, scores you on each work element in NICET's content outline, and weights each one by its share of the exam.

  • Your score shows after 20 answered questions and moves as you study.
  • It shows which work elements are pulling your score down, so you know what to study next.
  • Timed exams count, and it won't read Exam Ready until you've scored 70% or better on a timed exam in the last 60 days.
  • Building · under 60
  • Borderline · 60–74
  • Exam Ready · 75 and up

The score is an estimate of how you'd do on the exam, not a guarantee of passing. NICET doesn't publish a fixed pass mark.

Start studying for WBSL Level III: Hydraulics and Water Supply Planning

24 lessons, 797 practice questions, a full-length 60-question timed exam and your readiness score for the NICET Water-Based Systems Layout Level III: Hydraulics and Water Supply Planning exam.
Start free

The first lessons of every level in each track are free. Have an account? Log in

Keep going